The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

Today's global market means that raw materials are sought and bought from all over the world. This creates an higher demand for a well-functioning supply chain. In our thesis we have studied a large paper mill in northen Sweden which experiences issues with flow of raw material. Our aim has hence been to examine which aspects affect the flow of raw materials to the mill, and how these can be adressed using an IT-system. The question we sought to answer was; What factors are important to consider and how do these affect the ability of an IT-system which will support the flow of raw material at the paper mill? We have found that the problems are strongly connected to the low amount of information sharing between the mill and the suppliers.

At Rottneros pulp mill mechanical pulp is bleached with hydrogen peroxide. The changes of bleaching chemicals that are used for different grades are taken from bleaching tables; however these tables are old and need to be updated. The purpose of this thesis was to be the basis of new documentation.In this thesis three pulps where studied with the aim to find the optimal bleaching chemical changes (total NaOH/VP-quote) for each pulp. The pulps were taken from the filter before the bleaching tower and the pulps were bleached in the lab. The most important pulp property in this study was the brightness and how that was influenced by the chemical dosages.

Competition of spruce fiber raw materials has increased dramatically in the last few years, leading to the fact that transportation costs in the current situation represents a much larger share of the total raw material cost. The Holmen-owned pulp industry Hallsta Paper Mill's location on the coast also constitutes a problem, because of the lack of raw material, which is much larger there, than for a pulp mill located in the hinterland. For a coastal industry it?s therefore natural to import much of the raw material by boat or to buy it from the timber terminals, in order to maintain good profitability. The purpose of this study was to analyze how the size of Hallsta Paper Mill timber supply area, without competition, with competition and with terminal use, affects the company ?s transport costs.

The author contacted designers Claesson Koivisto Rune Arkitektkontor in August 2007regarding his Master thesis at KTH. The company had discussed the possibility of creating achair made from molded pulp. The author was taken on as a manager for the project. Theobjective was to produce design documentation for a paper pulp chair which was to belaunched at the in 2008 Milan Furniture Fair. The purpose of the thesis was to develop aproduct with scientific methods as well as to investigate how to make collaboration betweendesigners and engineers easier through communication.The project went through four basic stages: Information, Analysis, Synthesis and Evaluation.Information on paper pulp, molded pulp, chair design, sitting postures and the existingmarket of molded pulp furniture.

Until the beginning of the 1900:th century the paper making process was handicraft. The paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard.

An analysis of a specific application of anaerobic wastewater treatment at a pulp and board mill, Stora Enso Skoghall, was carried out. A literature study was done and effluent wastewater from CTMP pulp production was analyzed. The analysis consisted of a broad constituent analysis and an anaerobic treatment trial. Results from these test where used to calculate the treatment effectiveness and resulting energy potential at the mill.The literature study and constituent analysis showed that toxicity of the water to be treated, due to wood extractives and sulphur content, was of concern. Detoxification chemicals targeting these constituents where used in the anaerobic treatment trial.

An analysis of a specific application of anaerobic wastewater treatment at a pulp and board mill, Stora Enso Skoghall, was carried out. A literature study was done and effluent wastewater from CTMP pulp production was analyzed. The analysis consisted of a broad constituent analysis and an anaerobic treatment trial. Results from these test where used to calculate the treatment effectiveness and resulting energy potential at the mill.The literature study and constituent analysis showed that toxicity of the water to be treated, due to wood extractives and sulphur content, was of concern. Detoxification chemicals targeting these constituents where used in the anaerobic treatment trial.

This thesis work was made for Södra Cell Mörrums bruk in Blekinge. The purpose of the work was to develop a computer model in the simulation program Extend for the removal and balance of organic oxygen consuming substances, measured as COD (Chemical Oxygen Demand), in the new biological treatment plant in the mill. The plant produces two different pulp products, TCF- (Totally Chlorine Free) pulp and ECF- (Elementary Chlorine Free) pulp, for sale. The different bleaching procedures affect the characteristic of the wastewater and thus the effectiveness of the biological treatment plant.In the model that was developed the COD in the wastewater was divided into five different COD-fractions: soluble easily degradable (SS), soluble hardly degradable (SR), soluble inert (SI), particulate inert (XI) and particulate biomass (XB). To create the model FlowMac? was used as a base.

Hallsta paper mill uses large amounts of water during the pulp and paper making processes. The wastewater is treated in two separate activated sludge processes referred to as BIO 1 and BIO 2. The main aim is to reduce the organic substance content, measured as COD (Chemical Oxygen Demand) before the wastewater is released into the environment. Since the effluent produced is very rich in organic substances, the addition of nitrogen (N) and phosphorus (P) are necessary to give satisfactory treatment results. Problems with sludge bulking sometimes occur which lead to increased levels of suspended matter and nutrients in the effluent.

The degree project is performed at Metso Kamfab. The production is aimed on machines everything from handling of fiber to paper pulp. Metso Fiber and Kamfab are using Pro/Engineer for design and blueprint production. The processing department types the NC-programs in notepad on the basis of the blueprints, the CAD-dates that already is there are not used. The aim with the work is to study if Kamfab can use CAM-system for processing and production of programs for their NC-machines.

The purpose of this master thesis was to study the water system for mechanically cleaned water at Skärblacka mill, in order to find and evaluate possibilities of using energy more efficiently. The thesis also includes an evaluation of the software tool ?Pumpanalys?Skärblacka mill produces pulp and paper. The large amount of water required is cleaned mechanically through filters and called mechanically cleaned water (MR0). The MR0 water is pumped out to the factory by four crude water pumps.

Abstract    Objective: The aim of the present study was to investigate if inclinometer estimates of arm posture during paper mill work differed between periods of different arm visibility. The aim was also to identify strategies for and difficulties in assessing body-visibility on video. Methods: The study consisted of two parts, where part 1 aimed to investigate the validity of observation-based assessment of arm posture during paper mill work. Study 2 was a survey among people with experience in assessing the posture of paper mill workers from video. Results: The total time for the right upper arm visibility indicates that it was on average visible in 54%, partly visible 15 %  and not visible 31%.

The aim of this report is to improve the fire safety at Hallsta Paper Mill in Hallstavik, Sweden. In order to do so large parts of a fire-protection management system for the paper mill has been created. The report begins with giving a general description of management structures and fire-protection management systems. An account is given for how management structures are designed, and how they should be implemented, maintained and updated. Thereafter follows a description of what routines and instructions should be included in a fire-protection management system..

The purpose of this paper is to through a conceptual definition, outline the meaning of integrated reporting. The empirical study aims to identify the development of integrated reporting in terms of driving forces and participants. We also intend to identify and explain the effects of integrated reporting and to describe, analyze and create an understanding of what is required of companies and the challenges an application of integrated can bring. To achieve the purpose of this paper, we have formulated a central question; What is integrated reporting and what will this development mean for companies?  To answer the central question of this paper we have chosen to apply a qualitative approach with case studies as a research strategy.